Haier Refrigerator HYC-610 User Manual download pdf (Page 7)

Proper usage of the Refrigerator

During the initial startup and continuous usage of the refrigerator, the following procedures should be

followed.

1.Power the refrigerator in a dedicated power socket. The voltage requirement is 220 VAC and 50

hz. When started, do not place any products in the refrigerator.

2.When the unit initially starts up, the buzzer alarm may sound. This is normal. You can push the

buzzer alarm button to cancel the sound. The buzzer alarm continues to work until the upper bottle

temperature reaches the range of 2 to 8 .

3.Make sure that both sensor bottles have glycerin solution of 10% concentration. Please refer to

item 4 in the Operation section for details.

4.This refrigerator has been factory preset to operate at a range of 2-8 1. It is not necessary to

adjust the temperature set point.

5.It usually takes several hours for the unit to reach the preset temperature. Once the unit's

temperature is stable, check the sensor bottle temperature to see if it matches the set point.

6.Turn on the light for the interior. Inspect the light to makes sure it functions properly.

7.Once a thorough inspection of the unit is completed, products can be loaded into the refrigerator.

Beware to not load too many warm products into the unit at one time.

The terminals for the remote alarm contact are located on the back of the unit cover panel. The contacts

are designed for 30 VDC and 2A load. The remote alarm contacts work in synchronization with the

buzzer alarm on the refrigerator. Therefore, the remote alarm can be terminated by pushing the buzzer

alarm button. However, in case of a power outage, the remote alarm contacts cannot be controlled by

the buzzer alarm.

Remote alarm condition: Open for Normal, Close for Abnormal

Remote alarm contact

Location of Refrigerator

Your refrigerator should be placed at a location that satisfies the following conditions. By doing so, the

optimum operating results can be achieved.

1)Firm, level floor surface

2)A place that is far away from any heat

source

3)Do not install a refrigerator in direct sunlight

4)Dry area

5)Clean area

6)Good ventilation

7)Ground protection

Installing the unit on a firm and flat floor surface

reduces the chance of excessive noise and

vibration.

Avoid placing the unit near any heat dissipating

devices such as a gas stove, radiator, oven and

other source of heat. The refrigerator would lose

its efficiency once the insulation is exposed to

heat.

If a unit is in direct sunlight, it may not function

properly and its life expectancy can be shortened.

Avoid placing the unit near damp areas such as a

water faucet and sink.

Avoid installing a unit in or near chemical

materials and materials that might have out-

gassing property. Also avoid dusty locations.

There must be sufficient space around the unit for

air ventilation. Lack of such space will reduce the

unit's cooling capability.

Grounding the refrigerator will prevent electrical

shock to operators if its electrical insulation

becomes weak.

An electrical power plug with a ground

prong must be used to power the unit.

This is to prevent electrical shock.

Do not use water lines to replace a

properly installed ground wire for

ground protection. This is because

many water lines are actually built with

non-conductors such as plastic.

Never use gas lines as the ground

protection for the refrigerator. This

action can be very dangerous.

Never use a telephone line or lightening

rod as a grounding protection for the

refrigerator. This is because during

lightening, there is a strong current

present which is extremely dangerous.

8)Do not place any objects on top of the

refrigerator.

Do not place the unit in an area where

objects can fall directly onto it. This is to

avoid damaging the refrigerator.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Haier Refrigerator HYC-610 User Manual Page 7

Comments to this Manuals

Related products and manuals for Fridges Haier Refrigerator HYC-610